Firmware Version:
Wireless
Linksys Extender
Setup
Wireless
Administration
Status
Site survey
|
Basic Wireless Settings
|
QoS
Basic Wireless Settings
redirect
Configuration View:
Manual
Wi-Fi Protected Setup
WPS:
Enabled
Disabled
Note: Disabling WPS also disables the WPS button on your device.
Local Wi-Fi MAC Address: 98:FC:11:B1:1B:66
Remote Wireless Bridges' Wi-Fi MAC Addresses:
Note:
When set to "Wireless Bridge" mode, this device will communicate only
with another WAP300N in "Wireless Bridge" mode. Wireless settings,
including wireless band, channel, channel width, security mode and
passphrase/key, are required to be the same on all networked wireless
bridges.
Wireless Band:
5 GHz
2.4 GHz
5 GHz Wireless Settings
Network Mode:
Mixed
Wireless-A Only
Wireless-N Only
Network Name (SSID):
Channel Width:
Auto (20 MHz or 40 MHz)
20 MHz Only
40 MHz Only
Wide Channel:
Channel:
Channel:
Auto
36 - 5.180GHz
40 - 5.200GHz
44 - 5.220GHz
48 - 5.240GHz
149 - 5.745GHz
153 - 5.765GHz
157 - 5.785GHz
161 - 5.805GHz
165 - 5.825GHz
SSID Broadcast:
Enabled
Disabled
2.4 GHz Wireless Settings
Network Mode:
Mixed
Wireless-B/G Only
Wireless-B Only
Wireless-G Only
Wireless-N Only
Network Name (SSID):
Channel Width:
Auto (20 MHz or 40 MHz)
20 MHz Only
Wide Channel:
Channel:
Channel:
Auto
1 - 2.412GHz
2 - 2.417GHz
3 - 2.422GHz
4 - 2.427GHz
5 - 2.432GHz
6 - 2.437GHz
7 - 2.442GHz
8 - 2.447GHz
9 - 2.452GHz
10 - 2.457GHz
11 - 2.462GHz
SSID Broadcast:
Enabled
Disabled
Wi-Fi Protected Setup
TM
Use one of following for each Wi-Fi Protected Setup supported device:
1. If your client device has a Wi-Fi Protected Setup
TM
button, click or press that button and then click the button on the right.
OR
2. If your client device has a Wi-Fi Protected Setup
TM
PIN number, enter that number here
and then click
OR
3. If your client asks for the router's PIN number, enter this number
in your client device.
Wi-Fi Protected Setup
TM
Use one of following for eachWi-Fi Protected Setup supported device:
1. If your client device has a Wi-Fi Protected Setup™ button,click or press that button and then click the button on the right.
OR
2. If your client device has a Wi-Fi Protected Setup
TM
PIN number, enter that number here
and then click
OR
3. If your client asks for the router's PIN number, enter this number
in your client device.
Wi-Fi Protected Setup
TM
Status:
Wireless Band:
Network Name (SSID):
Security:
Encryption:
Passphrase:
Wi-Fi Protected Setup
TM
Status:
Unconfigured
Wireless Band:
Network Name (SSID):
Security:
Encryption:
Passphrase:
Help...
Save Settings
Cancel Changes
Configuration View
redirect
Two wireless networks with the same name have been detected on two different radio bands. Please select the one you would like to connect to:
2.4 GHz Band
5 GHz Band
Configuration View:
Manual
Wi-Fi Protected Setup
TM
Frequency Band:
5 GHz
2.4 GHz
Both
Network Name (SSID):
Channel Width:
Auto (20MHz or 40MHz)
20MHz only
Wireless Security
Security Mode:
WPA2/WPA Mixed Mode
WPA2 Personal
WPA Personal
WEP
Disabled
Encryption:
104 / 128-bit (26 hex digits)
40 / 64-bit (10 hex digits)
Passphrase:
Key 1:
Key 2:
Key 3:
Key 4:
Tx Key:
Key1
Key2
Key3
Key4
Authentication:
Open
Shared
Auto
Encryption:
TKIP
AES
TKIP or AES
Passphrase:
Wi-Fi Protected Setup
TM
Use one of following for eachWi-Fi Protected Setup supported device:
1. If your router has a Wi-Fi Protected Setup button, click or press that button, and then click the button on the right.
OR
2. If your router asks for the client device's PIN number, enter this number
in your router and then click
Link Status:
Network Name (SSID):
Security:
Link Status:
Disconnected
Network Name (SSID):
Security:
Help...
Save Settings
Cancel Changes
OK
Cancel Changes