The System Summary screen displays the router's current status and settings. This information is read only. If you click the button with underline, it will hyperlink to related setup pages. On the right side of the screen and all other screens in the Utility will be a link to the Site Map, which has links to all of the Utility's tabs.

System Information
Serial Number:
The serial number of the RV082 unit.
System up time:
The length of time in Days, Hours, and Minutes that the RV082 is active.
Firmware version:
The current version number of the firmware installed on this unit.
CPU: The type of the RV082 processor. It is Intel IXP425.
DRAM: The size of DRAM on the board. It is 32MB.
Flash: The size of Flash on the board. It is 16MB.

Configuration
If you need help to re-configure the router, click the Setup Wizard button.

Port Statistics
Users can click the port number from port diagram to see the status of the selected port. If the port is disabled, it will be read; if enabled, it will be black; if connected, it will be green. In summary table, it will show the setting of the port selected by users, such as Type, Link Status(up or down), Port Disable (on or off), Priority (High or Normal), Speed Status(10Mbps or 100Mbps), Duplex Status(half or full), Auto negotiation (on or off) and VLAN (VLAN group). In statistics table, it will show the port receive/transmit packet count/packet byte count and Port Packet Error Count of the selected port.

Network Setting Status
LAN IP: It shows the current IP Address of the Router, as seen by internal users on the Internet, and hyperlinks to LAN Setting on Network page of the Setup Tab.
WAN1 IP: It shows the current WAN1 IP Address of the Router, as seen by external users on the Internet and hyperlinks to WAN Connection type in Setup page. When users select Obtain an IP automatically and it shows two buttons, release and renew. Users can click release button to release the IP that users have already got and click renew button to update the DHCP Lease Time or get a new IP. When users select PPPoE or PPTP, and it shows Connect / Disconnect.
WAN2/DMZ IP: It shows the current WAN2 IP Address of the Router, or DMZ IP when DMZ selected, as seen by external users on the Internet and hyperlinks to WAN Connection type on the Network page of the Setup Tab.
Mode: It shows the Working Mode (Gateway or Router) and hyperlinks to Dynamic Routing section on the Advanced Routing page of the Setup Tab.
DNS: It shows all DNS Server Addresses and hyperlinks to WAN Connection Type on the Network page of the Setup Tab.
DDNS: It shows the status (Enable / Disable) and hyperlinks to DDNS page of the Setup Tab.  
DMZ Host: It shows DMZ Private Address and hyperlinks to DMZ Host page of the Setup Tab. The default is disabled.

Firewall Setting Status
SPI (Stateful Packet Inspection): It shows the status (On/Off) and hyperlinks to the General page of the Firewall Tab.
DoS (Denial of Service): It shows the status (On/Off) and hyperlinks to the General page of the Firewall Tab. 
Block WAN Request: It shows the status (On/ Off) and hyperlinks to the Block WAN Request section on the General page of the Firewall Tab.

VPN Setting Status
VPN Summary: It hyperlinks to Summary page of VPN Tab.
Tunnel(s) Used: It shows the number of Tunnels Used.
Tunnel(s) Available: It shows the number of Tunnels Available.
Current Connected (The Group Name of GroupVPN1) users: It shows the number of users.
Current Connected (The Group Name of GroupVPN2) users: It shows the number of users.
(If GroupVPN is disabled, it will shows No Group VPN was defined.)

Log Setting Status
It hyperlinks to the System Log page of Log Tab.
If you have not set up the mail server in Log page, it shows “E-mail cannot be sent because you have not specified an outbound SMTP server address." If you have set up the mail server but the log has not been come out due to Log Queue Length and Log Time Threshold settings, it shows “E-mail settings have been configured." If you have set up the mail server and the log has been sent to the mail server, it shows “E-mail settings have been configured and sent out normally." If you have set up the mail server and log can not be sent to mail sever successfully, it shows “E-mail cannot be sent out, probably use incorrect settings."